Thirty-Second Pen

Two are the pens in this picture are new.  The green and gold one is from the previous post.  There is also a red and gold pen but it is a new one.  The last one is a combination of green, red and gold.

Thirty-First Pen

This is the second acrylic pen I made.  The colors are Spring Green and Aztect Gold.  I think I should have added more green because it looks dull to me.

Thirtieth Pen

This is the first acrylic pen I made that turned out the way it was supposed to.  I made one before that didn't make it.  The colors was Red Russet and Aztect Gold.

Acrylic Pen Setup

I recently bought supplies to start making acrylic pens.  I found a video on Youtube of someone going through the steps to make one.  It seemed pretty easy so I gave it a try.  The very first time was a little rough, but it has gotten easier since then.  I ordered the Pearl Ex color off of Amazon, I bought the casting resin and hardener from Micheal's and I had the PVC pipe at home and I made the stand and quarks. The pens turn out really well.

Twenty-Nineth Pen Ambrosia Maple

These are two pens I made from Ambrosia Maple wood.

Twenty-Eighth Pen Makore

These are two pens I made from Makore wood.

Twenty-Seventh Pen Movingui

These are two pens I made from Movingui wood.  I really like the color of this wood.  I think it stand out among the others.

Twenty-Sixth Pen Morado

These are two pens I made from Morado wood blanks.

Twenty-Fifth Pen East India Rosewood

This is a pen I made from an East India Rosewood blank.

Twenty-Fourth Pen Limba

These are two pens I made out of Limba wood.  I wasn't sure how this would look at the end, but I actually like it a lot.

Twenty-Third Pen Wamara

These are two pens I made out of Wamara wood.

Twenty-Second Pen Purpleheart

This was a pen I made from a Purpleheart blank, although I don't think it looks very purple.

Twenty-First Pen

These are the two pens I made from Hawaiian Milo blanks.

Twentieth Pen Buckeye Burl

These are the two pens made from the Buckeye Burl blanks. I really like the look of these.

Nineteenth Pen Bubinga

These are two pens I made from some of the Bubinga blanks.

Eighteenth Pen Leopardwood

These are the two pens I made out of some of the Leopardwood blanks I ordered.

Seventeenth Pen Cocobolo

My plan for all of the wood I ordered was to make two pens out of each type of wood, to see what each type of wood looks like when finished and because as much as I like making designs, I also like the look of just solid, natural wood.  The first two are made from Cocobolo, which I really liked.  I went through the normal steps when making this pen.

Table Saw Sled

I have been looking at pen blank designs on the internet and have been a lot of designs that use pieces cut at different angels.  I would like to the to create some of these designs in the future.  I'm a little nervous about using the Compound Miter Saw to cut the angels because the pieces are so small, so I try to avoid it.  I've been using the band saw to free hand the angled cuts I've been making so far, and even though they're pretty good, they still need sanding afterwards and I have made some sub-par cuts in the past.  And using just the miter gauge on the table saw also makes me nervous.  So I decided to make a sled for the table saw to use.  The one thing I think I'll always like more about using the band saw over the table saw is the thickness of the blade.  The band saw produces less direct waste from cutting than the table saw does.  But if I need to sand the piece after I cut it on the band saw then there's probably not much different in the end.  I did some research online and built the sled in the pictures below from extra pieces around the shop.  I also made angles guide pieces from thin plywood to use in the sled.  I made 45, 60, 30 and 15 degree guides.  The guides have a pieces of wood glued to the top so that it can be clamped to the back fence.  The sled works pretty well, and I can cut pieces at certain angels at consistent widths.  I incorporated a stop-block on the right side so that I could control how wide the piece would be.  But I quickly found out that having the blank up against the angled guide and also pressed against the stop-block violated the "Don't use a miter gauge and fence together" rule.  I almost had the saw shoot the thin piece of would I was cutting out of the sled.  So I moved the stop-block a few inches to the right and clamped it to the fence.  Then I found another piece of wood that I could place to the left of the stop-block to butt the blank up against, then remove before I made the cut.  So the piece isn't being pinched between anything.  After the cut the loose stop-block can be placed back in, the blank slid down until it touches, the loose piece removed and another cut made.  But once I get down to a little over an inch of blank left, my fingers are too close to the blade for comfort.  But I don't want to waste material.  So i want to get a toggle clamp to somehow mount on the sled so the smaller pieces of the blank can be held on place so less wood is wasted.  There's still some other things I want to tweak on the sled, but overall it works well.

Table Saw Sled

Underside of the sled

Sled with the angled guides

Sled with guides and stop-block clamped down and pieces that have been cut

New Material Part 5

I also found on eBay people selling wood veneer, which is great because I like incorporating veneer lines in my pens.  I found someone who sells a variety of veneer in packs, so I bought one of those.  The woods included in the pack are: Zebra Wood, Teak, Eucalyptus, Sapele, Makore, Bubinga, Fig. Makore, Monique, Cypress Rosewood, Ebony, Birdseye Maple, Brazilwood.  The seller packed a lot of veneer into a small package.  I'm excited to incorporate some of these veneers in future pens.

New Material Part 4

These are the last of the wood blanks I ordered from eBay. 

Ambrosia Maple

Cocobolo Rosewood

East Indian Rosewood

Morado

Movingui

Makore

New Material Part 3

Here is another batch of pen blanks I ordered.  They came from the same person as part 2.  I'm really excited to work with the Purple Heart and Movingui.

Bubinga

Cocbolo Rosewod

Limba

Makore

Morado

Movingui

Purple Heart

Red Heart

New Material Part 2

   Here are some pictures of more pen blanks I ordered through eBay.  I decided that I'm going to make two pens that are plain and just showcase the wood and then use the remaining blanks of each wood the make different designs.  These blanks came from two lots by one vendor on eBay.

Ambrosia Maple

Cocobolo Rosewood

Cocobolo Rosewood

East Indian Rosewood

Leopard Wood

Makore

Morado

Redheart

Wamara

New Material Part 1

   I recently discovered on eBay that people sell lots of exotic wood pen blanks or boards of exotic woods.  This is a good and bad thing.  Good because I can start doing some different designs with the pens and bad for my wallet.  But I can deal with that later.  Here are some pictures of the first shipment of new pen blanks.

Buckeye Burl

Hawaiian Milo

Hawaiian Sugi

Pomelle Bubinga